Plumbing Insurance Home > Plumbing Insurance > Articles

Plumbing Insurance :: What of it? (April '08)

British Gas Product	British Gas Price	Homeserve Product	Homeserve Price	Saving with Homeserve
Homecare Flexi 100 (boiler and controls)	£9.00	EasyPay Boiler Cover (boiler and controls)	£5.99	£3.01
Homecare 100 (boiler and controls)	£12.00	Boiler Cover (boiler and controls)	£8.99	£3.01
Homecare Flexi 200 (Central heating)	£11.00	EasyPay Gas Central Heating Cover (Central heating)	£7.99	£3.01
Homecare 200 (Central heating)	£16.00	Central Heating Cover (Central heating)	£11.99	£4.01

Homeserve - combined plumbing insurance, electrical and utility cover - From £7 a month - home maintenance & local emergency repairs services. They can bring you the best insurance cover and insurance quotes, quotes for UK landlords and house residents. 

Plumbing, drainage & emergency plumbing repairs insurance from only £3.99 per month. Find out more to get a home insurance quote for emergency repairs with trusted local home maintenance providers 24 hours a day.  If you are a UK landlord who doesn't have time to deal with the home maintenance repairs on your properties, you could try Homeserve policies, with coverage from electrics to pest control and emergency repairs.

Call in the experts for any serious plumbing insurance or drainage problem!

· How to put up a shelf.

· How to change a fuse in a plug.

· How to check and change a fuse in a car.

· How to fit a smoke alarm.

· How to fit a new toilet seat.

· Read your electricity and gas meters.

· How to bleed your radiators.

How to put up a shelf. ----------------------------------------------------------------------------------------

What you need:
Screws (may be provided with the shelf – if not then don’t get screws too long, around 40mm)
Pencil
Masonry plugs (rawl plugs)
Masonry drill (2mm wider than the screw width)
Hammer
Spirit level
A shelf and brackets

Step 1

Decide where you want your shelf to go, and using the spirit level draw a line where you want the bottom of the shelf to go. Don’t draw too hard. Put 1 of the brackets on the line so that it lines up with where you want the shelf to sit. Hold the bracket up and draw through the holes where the screw goes, so you know where to drill. Leave about 5 inches of overhang at the end of the shelf.


Now do the same with the other bracket, leaving a gap between the 2 (depends on the length of your shelf). Remember to line this one up in the same way on the line you drew. Draw through the bracket holes.


Step 2

Get the drill out. Set it to drill clockwise and drill your holes where you marked earlier. Be a bit careful, if you’re drilling into plasterboard then there could be wiring inside, if in doubt use a no-contact current & voltage detector (cheap and useful) – simply turn the device on and bring it to the wall to see if it detects a current close (which means there could be wiring inside the wall).

Step 3

Once you’ve drilled your holes, put each of the masonry plugs into the holes and tap them gently in with a hammer so each is almost flat the wall.

Step 4

Use a screw to put up 1 bracket in the top hole only so it hangs, and tighten it a little. Now do the same with the other bracket, and place the shelf on top to check it lines up using the spirit level again.

Step 5

Screw in the other screws and tighten them. Now place the shelf on the brackets and attach these to the brackets (this varies between designs, many are a short screw upwards into the shelf). Admire your skills!

BACK TO TOP OF PAGE


-------How to check and change a fuse in a car. ---------------------------------------------------------

What you need:
New fuses of the correct amps
Pliers

Have your wipers or lights or electrics windows stopped working? It could be a fuse, and it’s easy to check…

Step 1

Find where your fuse box is located, it’s often inside the interior, under the steering wheel or it can be in the engine bay in a box.

Inside the fuse box will be all the blade fuses lined up. Usually the positions are labelled on the underside of the lid, look for the function e.g. the lights, that aren’t working and use the guide to find the correct fuse. If the fuse box doesn’t have a guide then check the car manual or search the internet for the fuse guide (almost everyone is available).

A Haynes manual will also have the fuse labelling diagrams inside.

Step 2

You should be able to pull out the fuse with your fingers but if it’s a bit stiff then use the pliers to carefully pull it out. You should be able to see if the fuse is blown because the metal connection joining the 2 metal prongs will be broken and melted, the fuse may be melted a bit too.

Get your new fuse (make sure it is the same amp rating as the old one, check the guide to confirm this) and simply slot it back into the hole, again being careful. Check it and you’re done!!

BACK TO TOP OF PAGE


-------How to fit a new toilet seat. --------------------------------------------------------------------------------

What you need:
A new toilet seat with fittings (available from most good hardware shops)
Pliers

Nothing breaks the concentration like an annoying busted toilet seat... So fix it! It's easy and quick and worth it.

Step 1

Now remember this is for regular toilet seats, not your space-age fruity designs which may have special fixtures... The seat is attached by 2 metal bolts that hold the seat hindge to the bowl. At the back under the seat will be 2 wing nuts, or jst plain nuts. Use a spanner or the pliers to undo the nuts if they are tight, turn them anti-clockwise to undo. Once the nuts are off you can simply lift the old seat upwards and the bolts will slip out, nice.

Step 2

Now you need to get the new seat, and put the 2 bolts attached to the seat back through the holes in the bowl. Remember to add any washers that may be provided with the seat. Now add another washer to the end of the bolts on the underside of the bowl, and do up the nuts a little. Now adjust the seat so it is positioned perfectly for optimal comfort, and tighten up the nuts! Bingo, a comfy crapper.

BACK TO TOP OF PAGE


Dont panic if you have drainage, plumbing, and insurance needs!
These chaps will come sort your plumbing problem or a drainage issue . 

-------How to bleed your radiators. ------------------------------------------------------------------------------

What you need:
Radiator bleed key (may not be needed if your radiator has an adjustable nut, just use a small spanner/wrench)

Radiators that don’t work properly is a real pain, but it’s not too tricky to fix if you think it’s air in the system. Here’s how!

It gets in there when you add new water, and can also build up due to the water pump.

How do you know? The tops of radiators will often be cold, or the whole radiator. Also high level pipes may not feel hot.

Turn of your central heating system. There’s no need to shut the whole thing off, just make sure the thermostat is turned right down so it won’t turn and start water pumping around and potentially all over your floor. It can get more air in too!

It works best with warm water in the system (the increased water pressure pushes the air out), simply turn the valve ANTI-CLOCKWISE until you hear a hissing, which is the air escaping. You can use a cloth to catch any water that may spray out.

Once Water starts to dribble out, tighten the nut/valve again (not too tight). Done! Try your heating, if the whole radiator now feels hot you’ve cracked it…

BACK TO TOP OF PAGE


-------How to change a fuse in a plug. ------------------------------------------------------------------------

What you need:
A new fuse (make sure it is the correct rating, check the appliance for guidance)
Screwdriver

Step 1

Unplug the appliance from the socket and turn it over so you can see the heads of the screws. Use a medium size screwdriver and undo the screws, turning them ANTI-CLOCKWISE. Once you have removed all 3 (or sometimes 2) turn the plug over to the top side and lift off the top half, be a bit careful to stop the fuse and pins dropping out.

Step 2

The fuse is situated in between 2 clips that link 2 pins together. Carefully unplug the dead fuse from the brass tops of the 2 pins, being careful not to pull the pins out of the bottom of the plug case. Clip in the new fuse (doesn’t matter which way), then replace the top half of the plug onto the bottom half. It will clip together nicely, make sure you don’t catch any of the wires between the plug casings as this can damage the wires, don’t force it!


Place the screws into the holes on the bottom of the plug and use the screwdriver to screw them back in (CLOCKWISE), until tight. Now test it!


If it’s still not working…

If you find it doesn’t work then check the connections and try the fuse in a different appliance that your know is working. The plug could also be dead, you can also test the plug by putting it onto an appliance you know works (with a working fuse) to see if the fault lies with the plug or the appliance.

BACK TO TOP OF PAGE



What you need.
Screws (should be provided with the shelf – if not then use screws that fit into the screw holes)
Washers
Masonry plugs (rawl plugs)
Pencil
Hammer
A drill with a masonry or wood drill bit (depends on what you’re are attaching the alarm too)
A smoke alarm a battery

Fitting a smoke alarm is a good idea, and it's not hard at all...

Step 1

Decide where you want it! It's best to have them on the ceiling near or in the kitchen or in a hallway.

Step 2

Get a ladder and get to the ceiling with your alarm and a pencil. Hold the alarm up and mark where the holes need to go. Don't do it near a light fitting! To be sure you don't drill into electrical cables it's a good idea to use a no-contact current & voltage detector (cheap and useful) – simply turn the device on and bring it to the ceiling to see if it detects a current close (which means there could be wiring inside the ceiling).

Step 3

Get your drill out and drill where you have marked with the pencil. Use a drill bit that's the right size for the masonary plugs (if it's wood you're putting it onto then just screw it straight in).

Step 4

Get up there and tap in lightly the masonry plugs with a hammer so they are flat with the ceiling. Put a washer over each screw so it sits by the screw head. Now screw the alarm into the masonry plugs with the screws that will have been provided with it. If you need screws then use ones that fit the holes in the alarm... Done!

BACK TO TOP OF PAGE


For professional advice and insurance for your drainage, plumbing, and insurance needs!
Click for the best insurance cover and insurance quotes, for pro help on your particular plumbing issue or a drainage problem . 

-------How to read your electricity and gas meter. ------------------------------------------------------


If you swap over your gas or electricity and you have meters then you'll need to give them a reading. It's rather simple really...



Step 1

You need to find where your meters are. They could be inside or outside in an external box of cupboard. Usually you'll need a special key to upen a box, it is often a triangular-ended key that is available from your gas supplier. Get it open!

Step 2

Now to read the guages. Reading either is the same, work your way from the left to the right guage, writing down the lower number next to the needle, so if the needle is betwen 6 and 7, then wrte down 6. Do this for each dial as you go until you will have a long number. That is your reading!



BACK TO TOP OF PAGE

Landlords never know when they'll'll need 24 hour electrical emergency repairs done to your home, electrical faults in your property can be a danger to those living there and can cause untold damage to your appliances.  Get electrical emergency home insurance cover for a low low monthly cost, and not only have cover for your electrical faults but also your plumbing, roofing, and so much more.  Electricians can be very expensive, why not take a look at the excellent insurance offers for landlords we have and get a fully qualified and vetted local emergency electrician 24 hours a day as part of your policy!   Gas central heating and plumbing repair insurance for Landlords - Just £17.66 per month Central heating maintenance and repairs can be very expensive, cover yourself in the eventuality of your electrical heating system or your gas central heating system getting a fault in one of your properties.  All repairs are carried out by local fully qualified CORGI registered boiler and heating engineers, and they will come 24 hours a day!  Faulty electric and gas heating boilers will cost you a fortune if they need a repair, get a quote on a landlords home maintenance insurance policy for peace of mind in those situations that can occur with your plumbing and electrics.  Landlords home insurance needn't be difficult, simply click here and see all the amazing services at the policies cover.  Plumbing insurance and plumbing service for rental properties - Find out more!

A gas leak in a landlords propertye can be a dangerous situation, shutting off your gas supply is key - and getting an expert to check the work or to fix the gas leak quickly and safely is essential.  Emergency gas engineers can be extremely expensive, take a look at our landlord insurance policies for the UK & Scotland, that cover emergency home maintenance, plumbing, electrical and gas call-outs 24 hours a day.   Landlords plumbing repairs, boiler and plumbing insurance for rental properties - Find out more! You can spot the early signs of a gas leak by installing a gas leak detector but the problem must be fixed immediately to stop any harm coming to the residents due to gas inhalation or fire.  If you have a gas fire in your home then see our article on the best things to do - .  Also call out an expert and the fire department to ensure the gas leak is dealt with safely! Your gas supply needs maintenance just like anything else in your house, protect your gas supply and installation with an excellent cheap landlords house insurance policy, no need for expensive call out costs again!  Plumbing insurance and emergency repairs for rental properties - Find out more!